Tools > Dust Collection
Blast Gates | Couplings | Dust Hoods | Elbows | Flanges | Floor Sweeps |
Flexible Hoses | Hose Clamps | Reducers | Separators | T's | Y's |
Dust collection is vitally important in maintaining shop cleanliness and the health of machine operators. The most efficient way to collect dust and debris is at the machines at the point of dust generation. Trying to remove dust from the air once it is released is much more difficult and less efficient. We carry a wide selection of dust collection hoses and components to outfit any system.
6" to 4" OD Duct Reducer ABS Plastic
TaytoolsThese reducers allow fitting of a 4" dust collection hose to a 6" hose. Opening on smaller end is: outer diameter 3.930" and tapers to 4" with inn...
View full details5.5" x 2.5" Dust Port Flange, 4" OD (DCE)
TaytoolsThis small dust port or flange can be used to collect dust from a variety of machines Overall size is 5.5" in diameter by 2.5" tall Opening is out...
View full details4" x 4" x 3.75" Angled Dust Port Flange, 2.5" OD (DCE)
TaytoolsThese small dust ports or flanges can be used to collect dust from a variety of machines. Overall size is 4" x 4" square base and 3.75" tall Openi...
View full details3.75" x 2.5" Dust Port Flange, 2.5" OD - 114885
TaytoolsThese small dust ports or flanges can be used to collect dust from a variety of machines. Overall size is 3.75" in diameter by 2.5" tall Opening h...
View full details24" x 7" x 2" Floor Sweep ABS Plastic, 4" OD
TaytoolsThis floor sweep can be secured to the floor and then debris can be swept inside and then vacuumed away with a dust collector Overall size: 24" wi...
View full details10" x 4" x 9" Deep ABS Plastic Dust Hood, 4" OD (114899) (DCE)
TaytoolsThese dust hoods can be used to collect dust from a variety of machines or can be placed on a table close to where dust is being produced. Built i...
View full details13" x 16" x 10" Deep ABS Plastic Dust Hood, 4" OD
TaytoolsThese dust hoods can be used to collect dust from a variety of machines or can be placed on a table close to where dust is being produced. These f...
View full details9.5" x 4.5" x 3.5" Deep ABS Plastic Dust Hood, 4" OD 114898
TaytoolsThese dust hoods can be used to collect dust from a variety of machines or can be placed on a table close to where dust is being produced. Made fr...
View full details13.5" x 7" x 6" Deep ABS Plastic Dust Hood, 4" OD
TaytoolsThese dust hoods can be used to collect dust from a variety of machines or can be placed on a table close to where dust is being produced. Built i...
View full details12" x 12" x 2.5" ABS Plastic Flange, 4" OD - 114906
TaytoolsUsed to connect dust collection hoses to the underside of a table saws, jointers, etc. Made from strong 1/8" thick abrasion resistant ABS plastic ...
View full details8" x 13.5" x 2.5" ABS Plastic Flange, 4" OD (DCE)
TaytoolsUsed to connect dust collection hoses to the underside of table saws, jointers, etc. Made from strong 1/8" thick abrasion resistant ABS plastic th...
View full details8" x 8" ABS Plastic Flange, 4" OD A85014 (DCE)
TaytoolsUsed to connect dust collection hoses to the underside of table saws, jointers, etc. Made from strong 1/8" thick abrasion resistant ABS plastic th...
View full details4" Blast Gate, Threaded End & Quick Disconnect End (DCE)
TaytoolsBoth openings are 1.25" long and taper from 3.85" to 4" and will fit 4" flexible hose or tapered dust fittings Made from strong 1/8" thick abrasio...
View full details4" OD Self Cleaning Anti Clog Blast Gates (DCE)
TaytoolsHas a gate that slides completely through the housing which is self cleaning and eliminates chip build up Both openings are 1.25" long and taper f...
View full details4” Dust Collection Cyclone Separator Kit for Trash Cans (DCE)
TaytoolsImprove your dust collector’s efficiency by converting to a two-stage unit with this 4" cyclone chip separator kit. The kit includes two elbows, tw...
View full details5 Pack 31” x 46” Clear Plastic Dust Collector Replacement Bags to Fit 20” Diameter Filter Drums Super Strong 5 mil Thick
TaytoolsEmpty your dust collection bags and replace with these economical, super thick 5 mil thick clear bags. These bags are designed to be used on the bo...
View full detailsIzzy Swan Quickloc System Starter Kits and Tool Plates (DCE)
TaytoolsThe QuickLoc System was designed by and currently manufactured by inventor, maker and content creator Izzy Swan. The Quickloc System allows you to ...
View full detailsAluminum Self-Cleaning Blast Gates 2-1/2", 3", 4", 5", and 6" OD (DCE)
TaytoolsWill fit 2-1/2", 3", 4", 5", or 6" diameter hoses or ducts Direct air flow to exactly where you need it and maximize dust extraction by opening an...
View full detailsMagswitch Quicklox Tool Plate
MagswitchThe Quicklox Tool Plate is a highly durable and easy-to-install component of the Quicklox system, providing a secure and stable base for connecting...
View full detailsMagswitch Quicklox Dust Bag Kit
MagswitchThe Quicklox Dustbag Kit is a simple yet ingenious solution for efficient dust management in the shop. Its quick-lock system allows for fast and ea...
View full detailsMagswitch Quicklox Hose Plate
MagswitchThe Quicklox Hose Plate is the counterpart to the Tool Plate, specifically designed to attach your dust collection hose to the Quicklox system. The...
View full detailsMagswitch Quicklox Tool and Hose Combo Kit
MagswitchThe Quicklox Tool and Hose Kit Combo is a revolutionary accessory designed to streamline the workflow in your woodworking shop. This system offers ...
View full details